ASM Metals Handbook Vol 15 Casting

ASM Metals Handbook Vol 15 Casting
اسم المؤلف
ASM International Handbook Committee
التاريخ
19 مايو 2016
المشاهدات
التقييم
Loading...

ASM Metals Handbook Vol 15 Casting
Table of Contents
Section Features
Front Matter
Preface
Table of Contents
Interactive Graphs
Applications and Specification Guidelines
1. History and Trends of Metal Casting
2. Metalcasting Technology and the Purchasing Process
3. Casting Design Issues and Practices
4. Casting Design and Processes Principles of Liquid Metal Processing
5. Chemical Thermodynamics and Kinetics
6. Thermodynamic Properties of Iron-Base Alloys
7. Thermodynamic Properties of Aluminum-Base and Copper-Base Alloys
8. Gases in Metals
9. Inclusion-Forming Reactions Melting and Remelting
10. Electric Arc Furnace Melting
11. Cupola Furnaces
12. Induction Furnaces
13. Vacuum Induction Melting
14. Electroslag Remelting
15. Vacuum Arc Remelting
16. Skull Melting
17. Electron Beam Melting
18. Plasma Melting and Heating
19. Crucible Furnaces
20. Reverberatory and Stack Furnaces Molten Metal Processing and Handling
21. Transfer and Treatment of Molten Metal – An Introduction
22. Degassing
23. Molten-Metal Filtration
24. Steel Melt Processing
25. Aluminum Fluxes and Fluxing Practice
26. Modification of Aluminum-Silicon Alloys
27. Grain Refinement of Aluminum Casting Alloys
28. Refinement of the Primary Silicon Phase in Hypereutectic Aluminum-Silicon Alloys Principles of Solidification
29. Thermodynamics and Phase Diagrams
30. Nucleation Kinetics and Grain Refinement
31. Transport Phenomena during Solidification
32. Plane Front Solidification
33. Non-Plane Front Solidification
34. Eutectic Solidification – An Introduction
35. Solidification of Eutectic Alloys – Aluminum-Silicon
36. Solidification of Eutectic Alloys – Cast Iron
37. Peritectic Solidification
38. Microsegregation
39. Macrosegregation
40. Interpretation and Use of Cooling Curves – Thermal Analysis
41. X-ray Imaging of Solidification Processes and Microstructure Evolution
42. The Oxide Film Defect – The Bifilm
43. Shrinkage Porosity and Gas Porosity
44. Castability – Fluidity and Hot Tearing
45. Semisolid Metal Processing
46. Spray Casting
47. Rapid Solidification
48. Solidification during Casting of Metal-Matrix Composites
49. Solidification Research in Microgravity
50. Homogenization
51. Heat Treatment
52. Hot Isostatic Pressing of Castings Modeling and Analysis of Casting Processes
53. Numerical Methods for Casting Applications
54. Modeling of Transport Phenomena and Electromagnetics
55. Direct Modeling of Structure Formation
56. Modeling of Microsegregation and Macrosegregation
57. Modeling of Stress, Distortion, and Hot Tearing
58. Practical Issues in Computer Simulation of Casting Processes
59. Thermophysical Properties Principles and Practices of Shape Casting
60. Shape Casting Processes – An Introduction
61. Patterns and Patternmaking
62. Casting Practice – Guidelines for Effective Production of Reliable Castings
63. Filling and Feeding System Concepts
64. Processing and Finishing of Castings Expandable-Mold Casting Processes with Permanent Patterns
65. Introduction – Expendable Mold Processes with Permanent Patterns
66. Aggregates and Binders for Expendable Molds
67. Green Sand Molding
68. No-Bake Sand Molding
69. Coremaking
70. Shell Molding and Shell Coremaking
71. Slurry Molding
72. No-Bond Sand Molding
Expandable-Mold Casting Processes with Expendable Patterns
73. Introduction – Expendable Mold Processes with Expendable Patterns
74. Lost Foam Casting
75. Investment Casting
76. Replicast Molding Centrifugal Casting
77. Centrifugal Casting
78. Horizontal Centrifugal Casting
79. Vertical Centrifugal Casting Permanent Mold and Semipermanent Mold Processes
80. Permanent Mold Casting
81. Low-Pressure Metal Casting
82. Low-Pressure Countergravity Casting High-Pressure Die Casting
83. High-Pressure Die Casting
84. Hot Chamber Die Casting
85. Cold Chamber Die Casting
86. Squeeze Casting
87. Vacuum High-Pressure Die Casting
88. Die Casting Tooling
89. Automation in High-Pressure Die Casting Semisolid Casting
90. Semisolid Casting – Introduction and Fundamentals
91. Thixocasting
92. Rheocasting
93. Thixomolding Cast Irons
94. Introduction to Cast Irons
95. Cast Iron Foundry Practices
96. Gray Iron Castings
97. Ductile Iron Castings
98. Compacted Graphite Iron Castings
99. Malleable Iron Castings
100. White Iron and High-Alloyed Iron Castings
101. High-Alloy Graphitic Irons Steel Castings
102. Steel Ingot Casting
103. Steel Continuous Casting
104. Shape Casting of Steel
105. Steel Castings Properties
106. Selection and Evaluation of Steel Castings Casting of Nonferrous Alloys
107. Nonferrous Casting – An Introduction
108. Dross, Melt Loss, and Fluxing of Light Alloy Melts
109. Aluminum Alloy Ingot Casting and Continuous Processes
110. Aluminum Shape Casting
111. Copper Continuous Casting
112. Casting of Copper and Copper Alloys
113. Casting of Zinc Alloys Nonferrous Alloy Castings
114. Aluminum and Aluminum Alloy Castings
115. Copper and Copper Alloy Castings
116. Zinc and Zinc Alloy Castings
117. Magnesium and Magnesium Alloys
118. Cobalt and Cobalt Alloy Castings
119. Nickel and Nickel Alloy Castings
120. Titanium and Titanium Alloy Castings
121. Zirconium and Zirconium Alloy Castings
122. Synthesis and Processing of Cast Metal-Matrix Composites and Their Applications Quality Assurance, Nondestructive Evaluation, and Failure Analysis
123. Approaches to Measurement of Metal Quality
124. Nondestructive Testing of Components
125. Casting Fracture Characteristics
126. Casting Failure Analysis Techniques and Case Studies
127. Common Defects in Various Casting Processes
128. Repair Welding of Castings
129. Quality Planning Tools and Procedures
130. Maintenance, Repair, Alterations, Storage of Patterns and Tooling Process Design
131. Riser Design
132. Gating Design
133. Design for Economical Sand Molding
134. Design for Economical Coring
135. Casting Design and Geometry
136. Design Problems Involving Thin Sections
137. Design Problems Involving Uniform Sections
138. Design Problems Involving Unequal Sections
139. Design Problems Involving Junctions
140. Design Problems Involving Distortion
Reference Information
Metric Conversion Guide
Abbreviations and Symbols
Index
كلمة سر فك الضغط : books-world.net
The Unzip Password : books-world.net

تحميل

يجب عليك التسجيل في الموقع لكي تتمكن من التحميل
تسجيل | تسجيل الدخول

التعليقات

اترك تعليقاً